Extensive selection of special designs

1.0 to 8.0 meter cleaning diameter
7 different spray pattern types available
suitable for use in FDA & EX environment
acid, alkali & temperature resistant
9 different ball sizes available
inexpensive to purchase, reliable operation
reasonable selection of high quality materials

Technical Data

Technical Data	Value
Max. Cleaning Diameter:	8 meters
Spraypattern:	90° up to 330°
Pressure-range:	0,5 – 20 bar
Flowrate:	0,1 – 1635 LPM (0,006 – 98,1 m³/h)
Insertion Opening:	15 mm up to 72 mm
Mounting position:	arbitrary
Materials:	Stainless Steel 316L (1.4404)
Standard connection:	Internal thread or clamping with union nut
Surface:	polished
Nozzle characteristic:	static ball with holes
Certificates:	3.1 DIN EN 10204, 2.2
Operating recommendation:	It is recommended to install a filter/strainer (500 μm) in the CIP supply line to the tank cleaner to protect it from particle clogging or damage.

High liquid volumes enable fixed spray balls to realize a thorough cleaning even at low pressure. By bombarding and rinsing the inner walls of the container the high cleaning effect is achieved. Adding suitable cleaning agents can even result in an improvement of the cleaning effect. As a consequence the cleaning time is shortened.

Two modes of operation are possible
– impulse-pause operation
– permanent flushing

Compared to the permanent blasting, the impulse-pause operation will cause a reduction of the cleaning liquid quantity while maintaining the same cleaning time. This procedure allows the cleaning medium that is used to develop its full effect.

Dimensions


TM 3/8“ up to 2“ until 330° possible, Flowrate on demand	TMA 1/8“ and 1/4“ until 300° possible, Flowrate on demand	TMÜ Clamping of the nozzle mouthpiece with union nut 3/8″, Flowrate on demand

Dimensions/connection types/flow rate/boreholes

G	Dimensions in mm			SW	max. V * (l/min) bei 3 bar	max. Bore number	max. bore Ø in mm
*V : Volume flow**
G	D	d	L	SW	max. V * (l/min) bei 3 bar	max. Bore number	max. bore Ø in mm
1/8″	13	13	26	11	16	13	1,0
1/4″	16	16	30	15	29	19	1,5
3/8″	24	21	36	22	45	37	2,0
1/2″	29	26	45	27	88	43	2,5
3/4″	34	31	54	32	181	74	3,0
1″	38	35	60	36	282	96	4,0
1 1/4″	50	50	78	46	410	108	5,0
1 1/2″	64	64	98	59	577	120	6,0
2″	70	70	106	64	1000	144	8,0

Volume flow for 1 drill (bore)

Bore- Ø (mm)	Volume flow in l/min at pressure p (bar) for 1 drill (bore)								max. recommended Tank-Ø (m)
Bores and distribution types possible according to customer requirements. When selecting the number and bore Ø, the volume flow should not be significantly exceeded.
Bore- Ø (mm)	0,5 bar	1 bar	2 bar	3 bar	5 bar	10 bar	15 bar	20 bar	max. recommended Tank-Ø (m)
0,6	0,10	0,14	0,20	0,24	0,32	0,45	0,55	0,63	0,3
0,8	0,20	0,28	0,40	0,45	0,60	0,89	1,10	1,26	0,4
1,0	0,35	0,50	0,70	0,85	1,10	1,57	1,92	2,21	0,6
1,5	0,75	1,07	1,50	1,83	2,37	3,36	4,11	4,74	1,0
2,0	1,20	1,70	2,40	2,93	3,79	5,37	6,58	7,58	1,5
2,5	2,05	2,91	4,10	5,00	6,48	11,2	11,2	12,9	2,0
3,0	3,00	4,26	6,00	7,32	9,40	13,5	16,4	19,0	3,0
4,0	4,20	5,96	8,40	10,4	13,3	19,7	23,0	26,5	5,0
5,0	7,00	9,90	14,0	17,1	22,1	32,8	38,4	44,2	8,0

Spritzmuster

Type F	Type B	Type I	Type G

300 – 330° Standard ab 3/8” 37 Bohrungen	180° Standard ab 3/8” 25 Bohrungen	180 – 300° bzw. 330° Standard ab 3/8” 25 Bohrungen	90 – 120° 90° 13 Bohrungen 120° 19 Bohrungen
Type N	Type P	Type O

on request	on request	Rohrreinigung

Typen/Varianten

Type TM – F – 330°

TM F – 330°	Flow rate l/min at pressure p (bar) 37 bore
Bore sizes and distribution patterns available to customer specification. When selecting quantity and bore diameter, the flow rate should not be significantly exceeded.
TM F – 330°	0,5 bar	1 bar	2 bar	3 bar	5 bar	10 bar	15 bar	20 bar
0,6	3,70	5,18	7,40	8,88	11,8	16,6	20,4	23,3
0,8	7,40	10,4	14,8	16,6	22,2	33,0	40,3	46,6
1,0	12,8	18,5	25,9	31,4	40,7	58,1	70,7	81,8
1,5	27,8	39,6	55,5	67,7	87,7	124	152	175
2,0	44,4	63,3	88,8	108	140	199	243	280
2,5	75,8	108	152	185	238	414	415	479
3,0	111	158	222	271	348	500	608	701
4,0	155	220	311	385	492	729	851	980
5,0	259	366	518	632	818	1214	1421	1635

Type TM – B + I – 180°

TM B+I 330°	Flow rate l/min at pressure p (bar) 25 bore
Bore sizes and distribution patterns available to customer specification. When selecting quantity and bore diameter, the flow rate should not be significantly exceeded.
TM B+I 330°	0,5 bar	1 bar	2 bar	3 bar	5 bar	10 bar	15 bar	20 bar
0,6	2,50	3,50	5,00	6,00	8,00	11,2	13,8	15,8
0,8	5,00	7,00	10,0	11,2	15,0	22,2	27,2	31,5
1,0	8,75	12,5	17,5	21,2	27,5	39,2	47,8	55,2
1,5	18,8	26,8	37,5	45,8	59,2	84,0	103	118
2,0	30,0	42,5	60,0	73,2	94,8	134	164	190
2,5	51,2	72,8	102	125	162	280	281	324
3,0	75,0	106	150	183	235	338	411	474
4,0	105	149	210	260	332	492	575	662
5,0	175	248	350	428	552	820	960	1105

Type TM – G – 120°

TM G – 120°	Flow rate l/min at pressure p (bar) 19 bore
Bore sizes and distribution patterns available to customer specification. When selecting quantity and bore diameter, the flow rate should not be significantly exceeded.
TM G – 120°	0,5 bar	1 bar	2 bar	3 bar	5 bar	10 bar	15 bar	20 bar
0,6	1,90	2,66	3,80	4,56	6,08	8,55	10,4	12,0
0,8	3,80	5,32	7,60	8,55	11,4	16,9	20,7	23,9
1,0	6,65	9,50	13,3	16,2	20,9	29,8	36,3	42,0
1,5	14,2	20,3	28,5	34,8	45,0	63,8	78,1	90,1
2,0	22,8	32,3	45,6	55,7	72,0	102	125	144
2,5	39,0	55,3	77,9	95,0	123	174	213	246
3,0	57,0	80,9	114	139	179	256	312	360
4,0	80,0	113	210	260	332	374	437	504
5,0	133	188	266	325	420	623	730	840

Type TM – G – 90°

TM G – 90°	Flow rate l/min at pressure p (bar) 13 bore
Bore sizes and distribution patterns available to customer specification. When selecting quantity and bore diameter, the flow rate should not be significantly exceeded.
TM G – 90°	0,5 bar	1 bar	2 bar	3 bar	5 bar	10 bar	15 bar	20 bar
0,6	1,30	1,82	2,60	3,12	4,16	5,85	7,15	8,19
0,8	2,60	3,64	5,20	5,85	7,80	11,57	14,17	16,4
1,0	4,55	6,50	9,10	11,0	14,3	20,4	24,8	28,7
1,5	9,75	13,9	19,5	23,8	30,8	43,7	53,4	61,6
2,0	15,6	22,1	31,2	38,1	49,3	69,8	85,4	98,5
2,5	26,6	37,8	53,3	65,0	84,2	118	146	168
3,0	39,0	55,4	78,0	95,2	122	176	214	246
4,0	54,6	77,5	109	135	173	248	299	344
5,0	91,0	129	180	222	287	426	499	575

Accessories

Installationslanze

Werkstoffe:	Edelstahl 1.4404 (316L), EPDM, FKM
Zertifikate:	3.1, 2.2
Geräteanschluss:	siehe Tabelle
Tankanschluss:	Flansch nach Bedarf
Sensor:	ohne SMW 100

Die dargestellten Angaben, technischen Daten und Informationen befreien den Anwender nicht von eigener Prüfung der gelieferten Produkte auf deren Eignung für den beabsichtigten Anwendungsfall. Alle Angaben sind ohne Gewähr. (Stand: 02.08.2022-71427321893-1888948-71042)

säurebeständig – Breconcherry Industrielle Reinigungssysteme

Spray balls TM-Series 1/8″ – 2″

Spray balls – TM-Series 1/8″ – 2″